Building a printed lightbox for a motionexpo vehicle or mobility display? This selection helps builders plan internal LED bars and service access for a pedestal-mounted graphic. Confirm the current organizer package before purchasing components for a separate build.
Where should the lightbox driver and connectors remain accessible?
Draw the lightbox, pedestal and vehicle display together. Mark a service route to the driver and connectors that does not require moving the vehicle or dismantling the graphic frame. Keep wiring away from pedestal joints and confirm ventilation and mounting requirements for the chosen supply.
Does an included mains connection power DC LED bars directly?
No. The three featured bars use DC24V and need a compatible supply between mains and the LED circuit. Add bar wattages, then verify supply capacity, polarity, connectors and cable loading. A stand package’s mains connection does not identify its lightbox driver or authorize changes to rented equipment.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Should I order modules if my booked stand already includes a lightbox?
Check first. Ask the organizer or builder what hardware, illumination and servicing are included. These components are for your own new lightbox or an explicitly approved modification; do not order replacements from a photograph alone. Measure the clear section and test the final transmitting print before confirming an LED layout.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all 26 options below. Send the graphic dimensions, clear lightbox section, pedestal access drawing and existing driver details for a component quote. LED bars do not include a pedestal, printed graphic, vehicle lighting or a complete organizer stand.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Building a printed lightbox for a motionexpo vehicle or mobility display? This selection helps builders plan internal LED bars and service access for a pedestal-mounted graphic. Confirm the current organizer package before purchasing components for a separate build.
Where should the lightbox driver and connectors remain accessible?
Draw the lightbox, pedestal and vehicle display together. Mark a service route to the driver and connectors that does not require moving the vehicle or dismantling the graphic frame. Keep wiring away from pedestal joints and confirm ventilation and mounting requirements for the chosen supply.
Does an included mains connection power DC LED bars directly?
No. The three featured bars use DC24V and need a compatible supply between mains and the LED circuit. Add bar wattages, then verify supply capacity, polarity, connectors and cable loading. A stand package’s mains connection does not identify its lightbox driver or authorize changes to rented equipment.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Should I order modules if my booked stand already includes a lightbox?
Check first. Ask the organizer or builder what hardware, illumination and servicing are included. These components are for your own new lightbox or an explicitly approved modification; do not order replacements from a photograph alone. Measure the clear section and test the final transmitting print before confirming an LED layout.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Compare all 26 options below. Send the graphic dimensions, clear lightbox section, pedestal access drawing and existing driver details for a component quote. LED bars do not include a pedestal, printed graphic, vehicle lighting or a complete organizer stand.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.