IEEE PES T&D is a transmission and distribution conference and exposition. This selection supports independent exhibit builders specifying printed backlit walls around large equipment displays, with attention to the space needed to access lightbox components.
Draw the service route with the exhibit equipment in place
Include the equipment footprint, lightbox access panel and intended LED mounting positions in the booth drawing. Check where a technician would reach the connector, external driver and fastening points without moving a large display object. A module that fits inside the empty frame may still be inaccessible once the exhibit is assembled. Keep the lightbox service route distinct from equipment controls and demonstration cables.
Sample the graphic and check the proposed access sequence
Test the actual printed face with the proposed source spacing and backing. Then review the planned access sequence using the component positions and available clearances: opening the lightbox, disconnecting the correct module and reaching its fasteners. Record the accepted source layout and service approach together. Recheck both if the equipment footprint or wall access changes; do not assume a smaller module alone resolves a blocked service route.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules replacement lights for electrical demonstration equipment?
This selection concerns internal light sources for independently designed printed booth lightboxes. It does not qualify modules for transmission equipment, utility installations or demonstration machinery. Confirm the lightbox model's voltage, connector and external supply separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, equipment footprint, access-panel position and source layout to discuss suitable component samples.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
IEEE PES T&D is a transmission and distribution conference and exposition. This selection supports independent exhibit builders specifying printed backlit walls around large equipment displays, with attention to the space needed to access lightbox components.
Draw the service route with the exhibit equipment in place
Include the equipment footprint, lightbox access panel and intended LED mounting positions in the booth drawing. Check where a technician would reach the connector, external driver and fastening points without moving a large display object. A module that fits inside the empty frame may still be inaccessible once the exhibit is assembled. Keep the lightbox service route distinct from equipment controls and demonstration cables.
Sample the graphic and check the proposed access sequence
Test the actual printed face with the proposed source spacing and backing. Then review the planned access sequence using the component positions and available clearances: opening the lightbox, disconnecting the correct module and reaching its fasteners. Record the accepted source layout and service approach together. Recheck both if the equipment footprint or wall access changes; do not assume a smaller module alone resolves a blocked service route.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these modules replacement lights for electrical demonstration equipment?
This selection concerns internal light sources for independently designed printed booth lightboxes. It does not qualify modules for transmission equipment, utility installations or demonstration machinery. Confirm the lightbox model's voltage, connector and external supply separately.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the lightbox section, equipment footprint, access-panel position and source layout to discuss suitable component samples.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.