Building a continuous illuminated graphic wall for IBC Amsterdam? Review the junctions between modular lightbox sections as well as their central areas. This selection supports fabricators comparing internal LED components for an assembled printed wall. All 26 products are available below.
Test a representative assembled joint
Build the sample with the intended frame connection, internal supports, cable passages and tensioned graphic. Compare the joint and adjacent panel centres from the viewing position. Record visible shadows, bands or source patterns; a central-panel sample cannot represent the junction. Recheck after changing a support position, cable route or joint arrangement.
Record the joint with each section's light-source layout
Keep the joint drawing and sample result with the LED model, mounting positions, quantity, voltage, connector and driver for each section. Confirm usable depth and installation access before ordering. Treat each product's mounting and electrical requirements separately; one model or chain limit does not apply to the entire catalog.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Do LED modules guarantee an invisible panel joint?
No. Frame construction, print tension, backing and source layout also affect the result. Test the actual assembly. These are printed-lightbox components, not video-wall seam calibration parts, broadcasting equipment or structural approval.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the panel-joint drawing, internal support locations, graphic face, usable depth and electrical plan for a component review. Compare the 26 products and retain the approved assembled-joint sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Building a continuous illuminated graphic wall for IBC Amsterdam? Review the junctions between modular lightbox sections as well as their central areas. This selection supports fabricators comparing internal LED components for an assembled printed wall. All 26 products are available below.
Test a representative assembled joint
Build the sample with the intended frame connection, internal supports, cable passages and tensioned graphic. Compare the joint and adjacent panel centres from the viewing position. Record visible shadows, bands or source patterns; a central-panel sample cannot represent the junction. Recheck after changing a support position, cable route or joint arrangement.
Record the joint with each section's light-source layout
Keep the joint drawing and sample result with the LED model, mounting positions, quantity, voltage, connector and driver for each section. Confirm usable depth and installation access before ordering. Treat each product's mounting and electrical requirements separately; one model or chain limit does not apply to the entire catalog.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Do LED modules guarantee an invisible panel joint?
No. Frame construction, print tension, backing and source layout also affect the result. Test the actual assembly. These are printed-lightbox components, not video-wall seam calibration parts, broadcasting equipment or structural approval.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the panel-joint drawing, internal support locations, graphic face, usable depth and electrical plan for a component review. Compare the 26 products and retain the approved assembled-joint sample.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.