Comparing signmaking materials after a Grimco Open House? Explore all 26 LED Modules products for independently built indoor graphic lightboxes. Keep the printed face and internal light source together in the sample review.
Bring a matched print offcut to the lightbox trial
Keep a reference offcut from the same translucent-media and print run as the intended graphic. Label its material, print orientation and any white-ink or backing treatment. An unprinted translucent sample cannot show how the finished artwork transmits light. Ask the builder to trial the printed offcut in the proposed frame with the candidate source.
Change one sample variable and retain the reference
When comparing edge-lit and rear-backlit layouts, document the frame depth, source positions, selected power supply and print treatment for each assembly. Keep the original reference available when reviewing another module or material. Check fine lettering, dark areas and the full graphic face; record which combination was reviewed rather than attributing a difference to the LED alone.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can a good-looking loose sample prove the production lightbox will match?
No. A loose print or exposed LED is not the completed optical assembly. Review the proposed source, mounting, frame and actual print together. Do not assume our modules replace a showcased supplier system or that an open-house demonstration used BOOTH LIGHTS products.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the labelled print sample, frame cross-section, proposed source positions and electrical details for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Comparing signmaking materials after a Grimco Open House? Explore all 26 LED Modules products for independently built indoor graphic lightboxes. Keep the printed face and internal light source together in the sample review.
Bring a matched print offcut to the lightbox trial
Keep a reference offcut from the same translucent-media and print run as the intended graphic. Label its material, print orientation and any white-ink or backing treatment. An unprinted translucent sample cannot show how the finished artwork transmits light. Ask the builder to trial the printed offcut in the proposed frame with the candidate source.
Change one sample variable and retain the reference
When comparing edge-lit and rear-backlit layouts, document the frame depth, source positions, selected power supply and print treatment for each assembly. Keep the original reference available when reviewing another module or material. Check fine lettering, dark areas and the full graphic face; record which combination was reviewed rather than attributing a difference to the LED alone.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Can a good-looking loose sample prove the production lightbox will match?
No. A loose print or exposed LED is not the completed optical assembly. Review the proposed source, mounting, frame and actual print together. Do not assume our modules replace a showcased supplier system or that an open-house demonstration used BOOTH LIGHTS products.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the labelled print sample, frame cross-section, proposed source positions and electrical details for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.