Updating a CPMA produce-show stand while retaining parts of an existing display? Compare all 26 LED Modules products for an independently built graphic lightbox. Keep the retained hardware specification separate from the new-source proposal.
Inventory retained and added lightbox components
Mark which frame sections, LEDs, drivers and harnesses are retained, newly purchased or rented. Record their actual labels, voltage, connector pin arrangement and mounting interfaces. An older frame being reusable does not establish that its LED bars or driver can run a new lightbox section.
Resolve the interface before mixing components
Ask the builder to identify exactly which existing components the proposed LED layout uses. Keep unsupported combinations out of the trial, and confirm rental modification conditions with the equipment owner. Review a sample containing the intended retained and new sections, using their proposed power supplies and prints. Record what was actually evaluated so the production order does not silently substitute another source or harness.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a familiar connector make old and new modules interchangeable?
No. A similar connector shape does not prove matching pin assignments, voltage, current requirements or mounting. This selection is for indoor graphic lightboxes, not produce-growing lamps or refrigeration lighting.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the retained-component inventory, frame drawings, proposed new sections and electrical interfaces for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Updating a CPMA produce-show stand while retaining parts of an existing display? Compare all 26 LED Modules products for an independently built graphic lightbox. Keep the retained hardware specification separate from the new-source proposal.
Inventory retained and added lightbox components
Mark which frame sections, LEDs, drivers and harnesses are retained, newly purchased or rented. Record their actual labels, voltage, connector pin arrangement and mounting interfaces. An older frame being reusable does not establish that its LED bars or driver can run a new lightbox section.
Resolve the interface before mixing components
Ask the builder to identify exactly which existing components the proposed LED layout uses. Keep unsupported combinations out of the trial, and confirm rental modification conditions with the equipment owner. Review a sample containing the intended retained and new sections, using their proposed power supplies and prints. Record what was actually evaluated so the production order does not silently substitute another source or harness.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Does a familiar connector make old and new modules interchangeable?
No. A similar connector shape does not prove matching pin assignments, voltage, current requirements or mounting. This selection is for indoor graphic lightboxes, not produce-growing lamps or refrigeration lighting.
Before ordering
Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the retained-component inventory, frame drawings, proposed new sections and electrical interfaces for an LED module comparison.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.