Looking for CFO Symposium fabric lightbox LED modules? A supplier documents SEG lightboxes and tablecloths for a sponsor at the CFO Magazine series. Compare independent sources for your own portable indoor display.
Where should the LED power supply go beside a draped sponsor table?
Choose its location using the power-supply maker’s installation and ventilation requirements. If your design places it near a tablecloth, prevent the drape from covering required openings or access; do not assume a concealed position is suitable.
What should I check when the table position changes at another venue?
Recheck cable routes, connector access and the driver’s surroundings with the final drape in place. Keep lightbox power requirements separate from laptops and other table equipment; confirm the complete setup before ordering repeat units.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these complete portable lightbox systems?
They are internal light sources. Check the separate power supply, controls, cables and frame needed for your display. No direct fit to the documented sponsor’s system is claimed.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send the frame depth, LED quantity, driver proposal and table/drape layout through Contact us to compare sources.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Looking for CFO Symposium fabric lightbox LED modules? A supplier documents SEG lightboxes and tablecloths for a sponsor at the CFO Magazine series. Compare independent sources for your own portable indoor display.
Where should the LED power supply go beside a draped sponsor table?
Choose its location using the power-supply maker’s installation and ventilation requirements. If your design places it near a tablecloth, prevent the drape from covering required openings or access; do not assume a concealed position is suitable.
What should I check when the table position changes at another venue?
Recheck cable routes, connector access and the driver’s surroundings with the final drape in place. Keep lightbox power requirements separate from laptops and other table equipment; confirm the complete setup before ordering repeat units.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Are these complete portable lightbox systems?
They are internal light sources. Check the separate power supply, controls, cables and frame needed for your display. No direct fit to the documented sponsor’s system is claimed.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Browse all LED Modules below. Send the frame depth, LED quantity, driver proposal and table/drape layout through Contact us to compare sources.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.