Planning printed brand lightboxes beside a CAOT Conference stage? This selection is for builders choosing internal LED bars for fabric or other transmitting graphics. Assess English and French branding from the audience positions, with the actual stage lighting in use.
How do I choose backlighting for a conference stage lightbox?
Make a working sample with the intended printed face, frame and supports. Check logos and both language versions from near and distant seats, including oblique views; keep important text away from frame edges. Balance the graphic with the surrounding stage rather than selecting the highest wattage alone. For recorded sessions, test the actual camera settings; no flicker-free performance is assumed.
Can I connect a lightbox to the stage dimming system?
Do not connect a low-voltage LED bar directly to a stage mains dimmer. The three featured bars require DC24V supplies, separately sourced and sized to the total load. Check the exact driver and controller before using any dimming system. The dual-CCT model needs compatible three-wire control; two white channels do not make it an RGB stage effect or establish DMX compatibility.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Will these LED modules light the conference speaker?
They illuminate a printed lightbox from inside. They do not replace speaker key lights, stage wash fixtures, a complete lightbox or its printed fabric. Keep speaker lighting and graphic backlighting as separate purchasing tasks. Compare edge-lit and rear-backlit candidates against the usable frame depth; an existing kit's brand or nominal width does not prove replacement fit.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the frame section and clear depth, printed-face dimensions, stage/seating layout, camera requirements and existing supply details. Ask for a compatible LED-bar sample and confirm the installation plan with the display owner and venue.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Planning printed brand lightboxes beside a CAOT Conference stage? This selection is for builders choosing internal LED bars for fabric or other transmitting graphics. Assess English and French branding from the audience positions, with the actual stage lighting in use.
How do I choose backlighting for a conference stage lightbox?
Make a working sample with the intended printed face, frame and supports. Check logos and both language versions from near and distant seats, including oblique views; keep important text away from frame edges. Balance the graphic with the surrounding stage rather than selecting the highest wattage alone. For recorded sessions, test the actual camera settings; no flicker-free performance is assumed.
Can I connect a lightbox to the stage dimming system?
Do not connect a low-voltage LED bar directly to a stage mains dimmer. The three featured bars require DC24V supplies, separately sourced and sized to the total load. Check the exact driver and controller before using any dimming system. The dual-CCT model needs compatible three-wire control; two white channels do not make it an RGB stage effect or establish DMX compatibility.
Compare LED lightbox sources
- 20W rigid edge-lit bar: 470×24×16mm including lens, DC24V, 2200lm ±10% and 10°×40° optics.
- 12W dual-CCT rear-backlight bar: DC24V, 1320lm, 180° beam and 3-wire JST; select the CCT pair and separate control.
- 10W slim edge-lit bar: 360×23×16mm including lens, DC24V, 1100lm and 9°×50° optics.
Will these LED modules light the conference speaker?
They illuminate a printed lightbox from inside. They do not replace speaker key lights, stage wash fixtures, a complete lightbox or its printed fabric. Keep speaker lighting and graphic backlighting as separate purchasing tasks. Compare edge-lit and rear-backlit candidates against the usable frame depth; an existing kit's brand or nominal width does not prove replacement fit.
Before ordering
For the three featured bars: Verify DC24V, total load, pinout and polarity; external power is separate. The dual-CCT bar also requires a compatible 3-wire switch or controller, not included. The featured slim 10W bar permits at most 6 per run after wiring checks; do not apply that limit to other models.
Send the frame section and clear depth, printed-face dimensions, stage/seating layout, camera requirements and existing supply details. Ask for a compatible LED-bar sample and confirm the installation plan with the display owner and venue.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.