REKLAMA POLYGRAF OBALY connects signmaking, print and POS suppliers. For an indoor printed lightbox, identify which side the customer will view before choosing an internal LED source. Browse all LED Modules below, then compare the source and frame against the actual graphic.
Mark the viewer side on the graphic and frame drawing
Label the intended viewing side, top edge and mounting orientation. Ask the printer to identify the printed surface and how it will face the viewer in the proposed material stack. Keep these labels with the source layout; front printing and rear printing require the print supplier to confirm the correct artwork orientation.
Check the installed message before changing the LEDs
After qualified assembly and wiring checks, read text and directional symbols from the intended viewing side with the lightbox illuminated. Record the printed face and frame orientation used for the trial. If the message is reversed, resolve the print or assembly orientation before adjusting LED quantity or spacing. Test the corrected print in the complete build.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can changing the LED bars correct reversed lettering?
No. A reversed message is an artwork or mounting orientation issue. Confirm the viewing side with the printer and fabricator, then evaluate illumination using the correctly oriented sample.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the marked frame drawing, intended viewing side, printed surface, graphic orientation, source candidates, sample observations and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
REKLAMA POLYGRAF OBALY connects signmaking, print and POS suppliers. For an indoor printed lightbox, identify which side the customer will view before choosing an internal LED source. Browse all LED Modules below, then compare the source and frame against the actual graphic.
Mark the viewer side on the graphic and frame drawing
Label the intended viewing side, top edge and mounting orientation. Ask the printer to identify the printed surface and how it will face the viewer in the proposed material stack. Keep these labels with the source layout; front printing and rear printing require the print supplier to confirm the correct artwork orientation.
Check the installed message before changing the LEDs
After qualified assembly and wiring checks, read text and directional symbols from the intended viewing side with the lightbox illuminated. Record the printed face and frame orientation used for the trial. If the message is reversed, resolve the print or assembly orientation before adjusting LED quantity or spacing. Test the corrected print in the complete build.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can changing the LED bars correct reversed lettering?
No. A reversed message is an artwork or mounting orientation issue. Confirm the viewing side with the printer and fabricator, then evaluate illumination using the correctly oriented sample.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the marked frame drawing, intended viewing side, printed surface, graphic orientation, source candidates, sample observations and quantity through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.