Light + LED Expo Mumbai includes LED modules, connectors and signage applications. For indoor illuminated graphics, draw the required wiring route before ordering internal lightbox components. Browse all LED Modules below.
Measure the route between actual connector positions
Mark bar positions, connector locations and the separate power-supply connection on the frame drawing. Measure the intended cable path around frame obstructions rather than the straight-line gap. Confirm access and strain relief with the frame supplier; do not pull a short lead tight to reach.
Separate cable reach from permitted electrical loading
Compare the required route with the selected model’s stated lead or included cable. Confirm any separately sourced harness, pinout and polarity before ordering. A cable that reaches does not establish an acceptable electrical run; keep connector and model-specific quantity limits separate from route length.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can a longer cable justify connecting more bars?
No. Cable reach and electrical loading are different checks. Review the chosen model, supply, harness and connection limits; do not extend a published bar-count limit because the route is longer.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the frame drawing, connector positions, measured cable route, bar model, planned quantities per circuit and harness details through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.
Light + LED Expo Mumbai includes LED modules, connectors and signage applications. For indoor illuminated graphics, draw the required wiring route before ordering internal lightbox components. Browse all LED Modules below.
Measure the route between actual connector positions
Mark bar positions, connector locations and the separate power-supply connection on the frame drawing. Measure the intended cable path around frame obstructions rather than the straight-line gap. Confirm access and strain relief with the frame supplier; do not pull a short lead tight to reach.
Separate cable reach from permitted electrical loading
Compare the required route with the selected model’s stated lead or included cable. Confirm any separately sourced harness, pinout and polarity before ordering. A cable that reaches does not establish an acceptable electrical run; keep connector and model-specific quantity limits separate from route length.
Compare LED lightbox sources
- 7W mini edge-lit bar: 200×23×16mm, DC24V, 770lm and standard 20°×60° optics; verify available mounting and removal space.
- 10W DC-plug edge-lit bar: 360×26×16mm including lens, DC24V, 1000lm ±10%, 15°×45° optics and dual-end DC sockets.
- Aluminum-profile edge-lit family: 22W/25W/32W, DC24V, 40.7×17mm housing and 14°×47° optics; specify length and wire exit.
Can a longer cable justify connecting more bars?
No. Cable reach and electrical loading are different checks. Review the chosen model, supply, harness and connection limits; do not extend a published bar-count limit because the route is longer.
Before ordering
These are internal light sources, not complete retail fixtures. Disconnect power before service. Verify DC24V, load, connector pinout and polarity; confirm power and hardware separately. The featured 10W DC-plug bar permits at most 6 per run after wiring checks. Do not transfer the limit to other models.
Send the frame drawing, connector positions, measured cable route, bar model, planned quantities per circuit and harness details through our contact page.
Contact us · Shipping policy · Organizer information
BOOTH LIGHTS is an independent supplier; no affiliation with or endorsement by the event organizer is implied.